How to use DA1469X pro kit mother board to debug target board

⚠️
Hi there.. thanks for coming to the forums. Exciting news! we’re now in the process of moving to our new forum platform that will offer better functionality and is contained within the main Dialog website. All posts and accounts have been migrated. We’re now accepting traffic on the new forum only - please POST any new threads at https://www.dialog-semiconductor.com/support . We’ll be fixing bugs / optimising the searching and tagging over the coming days.
9 posts / 0 new
Last post
jlzheng
Offline
Last seen: 1 year 6 months ago
Joined: 2020-02-14 02:15
How to use DA1469X pro kit mother board to debug target board

Hi, Dialog,

We use da14695 db on our targrt design, so need to connect pro kit mb to 14695 db with SWD lines.  We connect db J4 to mb J3, using P0_11 as swdclk, P0_10 as swdio, but  failed,  the message is  "Could not connect to target. Please check power, connection and settings."

How can I get it work?

thanks.

JL Zheng

 

Device: 
MHv_Dialog
Offline
Last seen: 1 year 2 months ago
Staff
Joined: 2013-12-06 15:10
Make sure that your wires are

Make sure that your wires are as short as possible (3inches max) and that GND connection is solid. It is also recommended to run the reset signal, but this should not be required.

/MHv

jlzheng
Offline
Last seen: 1 year 6 months ago
Joined: 2020-02-14 02:15
Thanks for your quick

Thanks for your quick response.

I cut the wire to less then 2 inches and still don't work, but ok when plug the db to mb socket. Anything else could I try?

thanks.   

KevinL
Offline
Last seen: 1 year 5 months ago
Staff
Joined: 2017-11-06 13:52
Hi Jizheng,

Hi Zheng,

Find S1 switch on the DK board, and disconnect M33_SWDIO and P0_10, M33_SWCLK and P0_11. Connect your target board SWDIO pin to TP49, SWCLK to TP54.

And make sure the DA1469x daugter board is on the mother board.

 

BR,

Kevin

 

jlzheng
Offline
Last seen: 1 year 6 months ago
Joined: 2020-02-14 02:15
Dear Kevin,

Dear Kevin,

Thanks for your advise. I need the DB to be on the target board,  also the test point is not a stable way to connect.  Could Segger OB work independently without DB?  So maybe other solution base on p0_10 and p0_11 exist? 

Best Regards,

JL Zheng

KevinL
Offline
Last seen: 1 year 5 months ago
Staff
Joined: 2017-11-06 13:52
Hi Zheng,

Hi Zheng,

Please provide 3V power to J4.28(V30) pin if you want to remove the DB. You can download the DK schematic from Dialog website.

 

BR,

Kevin

PM_Dialog
Offline
Last seen: 7 months 1 week ago
Staff
Joined: 2018-02-08 11:03
Hi Zheng,

Hi Zheng,

Apologies but I cannot understand your last comment. I read the previous comments and your requirement is to program your custom board using the Pro-DK. MHv_Dialog and KevinL have already let you know how to do it. Did you try our suggestions?

Thanks, PM_Dialog

jlzheng
Offline
Last seen: 1 year 6 months ago
Joined: 2020-02-14 02:15
Hi, PM_Dialog and Kevin,

Hi, PM_Dialog and Kevin,

Thanks Kevin for providing the answer to solve the problem,  others are optional.

BR,

JL Zheng

PM_Dialog
Offline
Last seen: 7 months 1 week ago
Staff
Joined: 2018-02-08 11:03
Hi Zheng,

Hi Zheng,

Thanks for accepting our answer and glad that you figured your issue out.

Thanks, PM_Dialog